14mm Strand Woven Bamboo Flooring

Short Description:

1) Materials: 100% Raw Bamboo
2) Colors: Strand Woven
3) Size: 1840*126*14mm / 960*96*15mm
4) Moisture content: 8%-12%
5) Formaldehyde emission: Up to E1 standard of Europe
6) Varnish: Treffert


Product Detail

Color Display

Installation

Carbonized Bamboo Flooring

Product Tags

Carbonized Bamboo Floor

Carbonized-Bamboo-Floor

How to choose Floating Bamboo Flooring?

Choose Best Floating Bamboo Flooring for your home , you need know how select.

Below is some Professional advice :

1.First look at the face:
There are no bubbles in the paint, whether it is fresh and bright, whether the bamboo joints are too dark, and whether there are glue lines on the surface (one by one uniform and straight line, the machining process is not fine, the heat pressure is not caused by other reasons) and then check whether there are cracks around , Whether there are any traces of ash. Whether it is clean and tidy, and then see if there is any remaining bamboo on the back, and whether it is clean and tidy. After reading everything, we need to inspect the goods to see if there is any difference between the sample and the actual product. The last item is installation. If the keel needs to be punched, it is about 30 cm in accordance with the standard. The standard plate needs four keels.

2.See features:
The color difference is small, because the growth radius of bamboo is much smaller than that of trees, and it is not seriously affected by sunlight, and there is no obvious difference between yin and yang. Therefore, the bamboo floor has rich bamboo patterns, and the color is uniform; the surface hardness is also one of the bamboo floors. advantage. Because the bamboo floor is a plant crude fiber structure, its natural hardness is more than twice that of wood, and it is not easy to deform. The theoretical service life is up to 20 years. In terms of stability, bamboo flooring shrinks and expands less than solid wood flooring. But in terms of actual durability, bamboo flooring also has shortcomings: delamination will occur under the influence of sunlight and humidity. Because of its higher specific heat and high density, its heat will not be lost in winter. Therefore, bamboo flooring has the performance of keeping warm.

3.Look at environmental protection:
For laminate flooring, the most important criterion for floor environmental protection is the amount of formaldehyde released. Regarding the limitation of formaldehyde emission standards, environmental protection in the floor industry has experienced three technological revolutions of E1, E0, and FCF. In the early stage, the formaldehyde emission standard of wood-based panels is E2 (formaldehyde emission ≤30mg/100g), and its formaldehyde emission limit is very loose. Even if it is a product that meets this standard, its formaldehyde content may exceed E1 artificial More than three times the size of the board, seriously endangering human health, so it must not be used for home decoration. Therefore, there was the first environmental protection revolution. In this environmental protection revolution, the floor industry implemented the E1 environmental protection standard, that is, the formaldehyde emission is ≤1.5㎎/L. Although it basically does not pose a threat to the human body, there are still residues in the floor. Many free formaldehyde. The flooring industry has begun the second environmental protection revolution, and introduced the E0 environmental protection standard, which reduced the floor formaldehyde emission to 0.5㎎/L.

4.Look at quality
Good floor should choose good material, good material should be natural, high and moderate density. Some people think that the higher the density of wood-based panels, the better. In fact, it is not. Too high density has a high water swelling rate, which can easily cause dimensional changes and lead to floor deformation. Secondly, it is necessary to rely on advanced flooring production lines and equipment and rigorous technology to produce first-class flooring.

Structure

bamboo-flooring-contructure
bamboo-types

Natural Bamboo Flooring

natural-bamboo-flooring

Carbonized Bamboo Flooring

Carbonized-Bamboo-Flooring

Natural Carbonized Bamboo Floor

natural-Carbonized-Bamboo-Floor

Bamboo Flooring Advantage

BAMBOO-FLOORING-ADVANTAGE

Details Images

18mm-Bamboo-Flooring
20mm-Bamboo-Flooring
15mm-Bamboo-Floor-Natural
Bamboo-Floor-Natural

Bamboo Flooring Technical Data

1) Materials: 100% Raw Bamboo
2) Colors: Strand Woven
3) Size: 1840*126*14mm / 960*96*15mm
4) Moisture content: 8%-12%
5) Formaldehyde emission: Up to E1 standard of Europe
6) Varnish: Treffert
7) Glue: Dynea
8) Glossiness: Matt, Semi gloss
9) Joint: Tongue & Groove (T& G) click Unilin+Drop click
10) Supply ability: 110,000m2 / month
11) Certificate: CE Certification , ISO 9001:2008, ISO 14001:2004
12) Packing: Plastic films with carton box
13) Delivery Time: Within 25 days after received advance payment

Click System Available

A: T&G Click

1

T&G LOCK BAMBOO-Bamboo Florinig

2

Bamboo T&G -Bamboo Florinig

B: Drop (short side)+ Unilin click (length side)

drop-Bamboo-Florinig

drop Bamboo Florinig

unilin-Bamboo-Florinig

unilin Bamboo Florinig

Bamboo flooring package list

Type Size Package NO Pallet/20FCL Pallet/20FCL Size of Box  G.W.  N.W.
Carbonized Bamboo 1020*130*15mm 20pcs/ctn 660 ctns/1750.32 sqm 10 plt,           52ctns/plt,520ctns/1379.04 sqms 1040*280*165 28kgs 27kgs
1020*130*17mm 18pcs/ctn 640 ctns/1575.29 sqm 10 plt,             52ctns/plt,520ctns/1241.14 sqms 1040*280*165 28kgs 27kgs
960*96*15mm 27pcs/ctn 710 ctns/ 1766.71 sqm 9 plt,            56ctns/plt,504ctns/1254.10 sqms 980*305*145 26kgs 25kgs
960*96*10mm 39pcs/ctn 710 ctns/ 2551.91 sqm 9 plt,            56ctns/plt,504ctns/1810.57 sqms 980*305*145 25kgs 24kgs
Strand Woven Bamboo 1850*125*14mm 8pcs/ctn  672 ctn, 1243.2sqm 970*285*175  29 kg  28 kg
960*96*15mm 24pcs/ctn 560 ctn, 1238.63sqm 980*305*145 26 kg 25 kg
950*136*17mm 18pcs/ctn 672ctn, 1562.80sqm 970*285*175 29 kg 28kg

Packaging

Dege Brand Packaging

DEGE-BAMBOO-FLOOR
DEGE-Horizontal-Bamboo-Floor
DEGE-BAMBOO-FLOORING
DEGE-Carbonized-Bamboo-Floor
bamboo-flooring-WAREHOUSE

General Packaging

Strand-Woven-Bamboo-Flooring-package
carton-bamboo-flooring
bamboo-flooring-package
bamboo-flooring-cartons

Transportation

bamboo-flooring-load
bamboo-flooring-WAREHOUSE

Product Process

bamboo-flooring-produce-process

Applications

strand-woven-bamboo-flooring
brown-Strand-Woven-Bamboo-Flooring
champagne-Strand-Bamboo-Flooring
natural-Strand-Woven-Bamboo-Flooring
bamboo-flooring-for-indoor
Coffee-Rustic-Bamboo-Floor
dark-Strand-Woven-Bamboo-Flooring
15mm-Strand-Woven-Bamboo-Flooring
teak-Strand-Bamboo-Flooring

  • Previous:
  • Next:

  • about17How is bamboo floor installed (detailed version)

      Bamboo wood floor installation is not much different from standard hardwood floor installation. For homeowners, the primary motivation for doing bamboo wood floor installation is to save money. It can be installed in half the cost by doing it yourself. Installing a bamboo floor can be an easy weekend project.
    Basic Instructions: Prior to installation of any flooring, you should ensure that the job site and subfloor meet the necessary requirements. The important steps in installation take place before putting in the bamboo floor.Here are a few guidelines:
    The first step in bamboo wood floor installation is making sure the subfloor is:
    √ Structurally sound
    √ Clean: Swept and free of debris, wax, grease, paint, sealers, and old adhesives etc
    √ Dry: Subfloor must remain dry year-round, and
    √ Level Adhesives do not bond well with dirty subfloors and will eventually cause decay, if moist. If not level, the bamboo flooring will squeak when walked on.
    √ Remove any old nails or staples from previous flooring material.
    √ Examine each floor plank for grade, color, finish, quality and defects.
    √ Measure the floor and divide by the number of boards.
    √  Lay out flooring for visual selection.
    The careful placement of color and grain will enhance the beauty of the finished floor.
    √ The flooring material must be stored at the installation site at least 24-72 hours earlier. This allows the flooring to adjust to the room temperature and humidity.
    √ Do not store directly on concrete or near outside walls.
    √  When purchasing flooring, add 5% to actual square footage needed for cutting allowance.
    √  If you’re installing the bamboo floor on a second story, then before using the nailer/stapler, first remove light fixtures from the ceilings below. The stapler puts a pressure on the joists and can loosen ceiling-mounted fixtures below.
    √  Any job involving water or moisture should be done before the bamboo wood floor installation. A room temperature of 60-70°F and humidity level of 40-60% is recommended.
    Important Note: A bamboo wood floor should be the last item installed for any new construction or remodel project. Also, install the floor per the manufacturer’s guidelines to protect your warranty.
    Installation Tools:
    √ Measuring Tape
    √ Handsaw (power saw is also helpful)
    √  Tapping block (trimmed piece of flooring)
    √ Wood or plastic spacers (1/4″)
    √ Crow bar or pull bar
    √  Hammer
    √  Chalk line
    √  Pencil
    For nail-down installation, you’ll also need:
    √  A hardwood-appropriate nail gun
    √  A nail application chart For glue-down installation, you’ll also need:
    √  Approved flooring adhesive
    √  Adhesive trowel
    For floating installation, you’ll also need:
    √  6-mil poly film foam underlayment
    √  PVAC glue
    √  Poly tape or duct tape
    Pre-installation Instructions:
    √  To make the flooring fit underneath, door casings should be undercut or notched out.
    √ As the wood expands with an increase in moisture level, a 1/4″ expansion space should be left between flooring and all walls and vertical objects (such as pipes and cabinets). This will be covered during the reapplication of base moldings around the room. Use wood or plastic spacers during installation to maintain this expansion space.
    √  Always use a tapping block and hammer to pull planks together. The tapping block should be used against the tongue only, never against the groove of the plank.
    √  Always begin each row from the same side of the room.
    √  A crow or pull bar can be used to close end joints near a wall.
    √  Take care not to damage the edge of flooring.
    Getting started: For the best appearance, a bamboo wood floor is often laid parallel to the longest wall or the outside wall, which is usually the straightest and suitable for laying down a straight working line. The direction of the planks should be based on the layout of the room and locations of entrances and windows. A few rows (no glue or nails) can be dry-laid before starting installation to confirm your layout decision and working line. If the room is ready for installation, and all materials and tools are present, a DIYer with some flooring experience can expect to install about 200 square feet in a day. Installment Procedure: There are three common ways for a bamboo wood floor installation: Naildown, gluedown and floating.
    1. NAILDOWN or SECRET NAILING: In this method, the bamboo floor is ‘secretly’ nailed down to a wood subfloor. It is the traditional way of bamboo wood floor installation using nails or staples. All solid flooring and many engineered floors can be installed this way. The floor joists (floor support beams) must be marked to guide installation procedure. Also, the location of floor joists should be marked on the felt paper with chalk lines. These markings will identify where nails and staples should be driven to make a solid connection with the subfloor. The nails or staples are rammed at an angle through the tongue and are hidden by the next piece of flooring. This is why it is called ‘blind or secret nailing.’ Nail each board every 8″ and within 2″ of each end. Once starter rows are placed, the next planks should be nailed directly above the tongue at a 45o angle. A face nail might be needed in doorways or tight areas where the nailer can’t fit. The last two rows will also have to be face nailed in the same manner. A good eye should be kept on nail / staple penetration.
    2. GLUING DOWN: This method involves the gluing of the bamboo floor to a subfloor. A glue-down wood floor is installed in a similar way like that of flooring tile. It can be used for installation on both concrete subfloors and on plywood. Engineered flooring can be installed using similar glue-down methods. Bamboo flooring can be glued down using a moisture resistant flooring adhesive (especially urethane type). Read adhesive instructions carefully for proper trowel size and adhesive set time. Water based adhesives should not be used for this purpose. Also, never use the “wet lay” or “loose lay” method of installing. Start with the outside wall and spread as much adhesive as can be covered by the flooring in 1 hour. After applying the adhesive to the subfloor with a trowel, the bamboo flooring planks should be immediately placed with groove facing the wall. Allow for adequate cross ventilation during the procedure. Make sure the floor is still aligned and be careful not to let installed floor move on the wet adhesive. Use damp cloth to immediately remove any adhesive that gets on flooring surface. Walk on the flooring foot-by-foot within 30 minutes of laying the floor to ensure a solid bond with the adhesive. Flooring planks on the boundary line of room may require weight for this bond.
    3. FLOATING FLOOR: A floating floor is attached to itself and not to the subfloor. It is installed over various types of cushion underlayment. This method is suitable with any subfloor and is especially recommended for radiant heat or below grade installations. Only wider engineered or cross ply products should be considered for floating. This method involves gluing the tongue and groove joints of the bamboo wood flooring together over an underlay. Start first row with groove toward wall. Glue end-joints of first row by applying adhesive to bottom of groove. Lay subsequent rows of flooring by applying glue to side and end joints and fitting planks together with tapping block.
    Post-Installation Care:
    √  Remove expansion spacers and reinstall base and/or quarter round moldings to cover the expansion space.
    √  Do not allow foot traffic or heavy furniture on floor for 24 hours (if glue-down or floating).
    √  Dust mop or vacuum your floor to remove any dirt or debris.

    spec

     

    about17Stair slab

    20140903092458_9512 20140903092459_4044-(1) 20140903092459_4044 20140903092459_6232

    20140903092500_0607

    20140903092500_3732

    20140903092500_6701

    about17Ordinary bamboo floor accessories

    4 7 jian yin

    20140904084752_2560

    20140904085502_9188

    20140904085513_8554

    20140904085527_4167

    about17Heavy bamboo flooring accessories

    4 7 jian T ti

    20140904085539_4470

    20140904085550_6181

    Characteristic Value Test
    Density: +/- 1030 kg/m3 EN 14342:2005 + A1:2008
    Brinell hardness: 9.5 kg/mm² EN-1534:2010
    Moisture content: 8.3 % at 23°C and 50% relative humidity EN-1534:2010
    Emission class: Class E1 (LT 0,124 mg/m3, EN 717-1) EN 717-1
    Differential swelling: 0.17% pro 1% change in moisture content EN 14341:2005
    Abrasion resistance: 16’000 turns EN-14354 (12/16)
    Compressability: 2930 kN/cm2 EN-ISO 2409
    Impact resistance: 6 mm EN-14354
    Fire properties: Class Cfl-s1 (EN 13501-1) EN 13501-1
  • Write your message here and send it to us

    RELATED PRODUCTS